FS/Free: Garage cleanout - Volvo/Honda/Chevy parts

[freakin]

I'm cleaning up my garage and need this stuff gone ASAP. Feel free to make an offer on any of the parts.


Volvo parts:
Slotted T cam FREE

S10/Sonoma parts:
All gone. :D

Chevy engine parts:
All gone as well. :P

Misc. stuff:
-4" steel pipe + flat steel used for fabricating air suspension. Lots left over, could build 2-3 more air suspension setup with what's left. GONE

Honda parts:
-D16A6 intake manifolds (PM6), have 2. Needed for DPFI to MPFI conversions. Include TB, IACV, most sensors, etc. FREE
-90-93 Integra rear hatch, black, in great shape. $40
-92-93 Integra trunk lid removed the wing, black. $20
-92-93 Integra 2dr. rear bumper (has lip on bottom), black, in great shape. $75
-90-93 Integra 4dr. rear bumper, white, in great shape GONE
-90-93 Integra 2dr. rear seat, small burn, dark blue/black. GONE
-88-89 CRX bumpers (no rebar). I have the a front in white as well as a front and back in black. All in really good shape. $40 each, $60 for pair
-88-98? OEM Honda CD deck, works, but don't have the code $30
-98+ OEM Honda CD deck, works, basically new, have the code SOLD
-Momo style steering wheel hub (please stop asking me about a wheel, I don't have one!). Was supposed to be for an EG , but I never tested it out. Seemed to fit my buddy's S13. If have no idea what the actual application is, came with a wheel I bought. You're welcome to try it out. GONE

NEW PARTS
-Crane stage 3 cams for B-series VTEC, 4,000KM, basically new $400
-JE 11.5:1 CR pistons for B20, 84.5mm bore, 4,000KM, basically new $450
-B-series OEM flywheel (18-20lbs) $25
-CRX rear bumper, white, 88-89 style $40
-CRX tail lights (corners + center), 88-89, great for replacing those nasty altezzas SOLD
-DC front knuckles, no hubs, great for going to 10" brakes on a Civic (grab the DA calipers below and you're set) $40 for the pair
-DA front front and rear calipers, freshly machined rotors, Axxis Ultimate pads (front only, 50% left) $50
-OBD-0 B16 exhaust manifold (top section only), includes o2 sensor FREE


PS, Beer is always welcome in exchange for the free parts. Asahi (mmmm JDM beer) or Grasshopper preffered. :poosie:

[kaput]

.

[freakin]

Those manifolds are the metal part that's attaced to the back of the head....basically the closest part of the motor to the firewall. What you're looking for is the intake piping. So what I have isn't going to work for you.

For anyone else, they're from 88-91 Civic Si motors, but they'll fit any D-series motor. I have no idea if they're an upgrade or not to stuff like the D15's or anything like that.

[euro_racer]

any picstures of the steering wheel?

[freakin]

It's only a hub. And sorry, I don't have any pics of it.....it just looks like any momo hub though...except that it's not collapsable like them, so it doesn't have that accordian style sleeve over it.

[78si]

pmed

[DALLEN]

PM'D

[freakin]

I've updated the lists with new stuff and what gone. I've stored the bumpers and some of the bigger stuff, but I'd still like to get rid of them.

And for the record, I do not have a momo steering wheel for sale. I've edited the post to make that more clear.

PS, please note the beer comment on the first post. :thumbsup:

[freakin]

List is cleaned up again....I've removed the stuff that's already gone. Lot's or Honda body parts left over that are taking up a ton of room. They're my first proirity to move. No reasonable offer will be refused for them.

[freakin]

One last bump.....I haven't had time to do the dump run yet, but I'm planning on this weekend. The bumpers are what I really want to get rid of.

[JordanEG6]

hey matt, do you have pics of the deck?

[freakin]

I'm not at home, but this is what both of them look like. I was corrected the other day....apparently the deck harness changed when the cars went to OBD-2, so it's 96+ and the other one is pre-96. I stole this pic from the internet...

http://www.oemvalue.com/pics/honda/hondafront.jpg

Let me know if you need an actual pic of either.

[JordanEG6]

so the deck wont plug into an EG that was previously OBDI?

[Rockski]

josh will take all chevy parts tomorrow, pm me

[freakin]

Originally posted by JordanEG6
so the deck wont plug into an EG that was previously OBDI?

I have 2, but the the OBD1 deck doesn't have a code. How does this sound? You can take the OBD1 deck and see if you can get the code for it. I can give you the vin number from the american gsr it came out of. If you can find that, and it works for you, then just pay me the $30 for it. If not, just return it.

[freakin]

Originally posted by JordanEG6
so the deck wont plug into an EG that was previously OBDI?

Jordan,
I have 2, but the the OBD1 deck doesn't have a code. How does this sound? You can take the OBD1 deck and see if you can get the code for it. I can give you the vin number from the american gsr it came out of. If you can find that, and it works for you, then just pay me the $30 for it. If not, just return it.


Originally posted by Rockski
josh will take all chevy parts tomorrow, pm me

Hey Josh,
I'll give you a call in an hour or so, once I get home.

[Rockski]

awesome

[freakin]

Bump, still looking to get rid of a lot of parts.

*List has new items and old items have their prices adjusted.*

[air_mikey]

check pm

[freakin]

Bump, lots of parts still left. Adjusted pricing a little to get rid of the engine parts.

[CoryR6civic2]

how about that momo steering wheel? :guns: :guns: ;) ;)

[kkoz]

do you have a pic of the rear bumper? is it the stock one or is there a aftermarket lip on it?

[1-Bar]

I'll take that flywheel :)

[freakin]

Originally posted by kkoz
do you have a pic of the rear bumper? is it the stock one or is there a aftermarket lip on it?

It's a stock bumper, no additional lip. I was just pointing out the difference between the shape of the 90-91 and the 92-93 rear bumpers.



Originally posted by 1-Bar
I'll take that flywheel :)

PM'd

[freakin]

bump, lots of stuff still sitting around.