Sorath
10-28-2008, 05:10 PM
Like to sell as a whole car, but would part out if enough interest
Rb25 series 2 engine with rb20 tranny custom driveshaft and act 6puck clutch $2500
ku engineering top mount exhaust manifold
Chromed cold side gt35r dual ball bearing turbo, cant remember if it was the .82 a/r or 1.06 a/r. 84 trim Together $1500
ku engineering Intake manifold with 90mm throttlebody (blue)
$1000
steel braided oil lines $offer?
tial 40mm external gate $400
Custom 3.5" turbo back exhaust $400
Autronic sm4 with wiring harness conversion $2500
Gtr Front End conversion (hood, bumper, grill, latch) $1000
Luminas Hids 6000k $200
Enkei nt03 rims 17x7 front 17x8 rear. brand new rubber on them $500
Greddy? Front mount intercooler with custom piping $600
Alpine deck 9831? $100
Cusco Front strut tower brace $80
Compustar 2wfm8000 $200
Momo steering wheel and shift knob $80
Reason for selling is because its been sitting for awhile, right now theres no intercooler piping and downpipe but can get it done if there are serious buyers. Car started good couple weeks ago.
for whole shell with other panels and stuff looking to get about $2500
Lots of mods not listed
Car came stock from japan, have done all mods in calgary alberta, most done by autodream.
Not gonna lie, Car needs some tender loving care.
not much left to do, whoever wants to finish my project, should be a killer.
this is what i ran at the track, couldnt hook on brand new 245 kumho ecsta spt's. 13.4 @ 109 mph
http://www.youtube.com/watch?v=dgnKrfV4a7c
Buy whole car for $12,000 FIRM
Old sale thread with pictures http://forums.beyond.ca/st/198417/fs-1990-nissan-skyline/
EDIT: NOT PARTING ANYMORE
Rb25 series 2 engine with rb20 tranny custom driveshaft and act 6puck clutch $2500
ku engineering top mount exhaust manifold
Chromed cold side gt35r dual ball bearing turbo, cant remember if it was the .82 a/r or 1.06 a/r. 84 trim Together $1500
ku engineering Intake manifold with 90mm throttlebody (blue)
$1000
steel braided oil lines $offer?
tial 40mm external gate $400
Custom 3.5" turbo back exhaust $400
Autronic sm4 with wiring harness conversion $2500
Gtr Front End conversion (hood, bumper, grill, latch) $1000
Luminas Hids 6000k $200
Enkei nt03 rims 17x7 front 17x8 rear. brand new rubber on them $500
Greddy? Front mount intercooler with custom piping $600
Alpine deck 9831? $100
Cusco Front strut tower brace $80
Compustar 2wfm8000 $200
Momo steering wheel and shift knob $80
Reason for selling is because its been sitting for awhile, right now theres no intercooler piping and downpipe but can get it done if there are serious buyers. Car started good couple weeks ago.
for whole shell with other panels and stuff looking to get about $2500
Lots of mods not listed
Car came stock from japan, have done all mods in calgary alberta, most done by autodream.
Not gonna lie, Car needs some tender loving care.
not much left to do, whoever wants to finish my project, should be a killer.
this is what i ran at the track, couldnt hook on brand new 245 kumho ecsta spt's. 13.4 @ 109 mph
http://www.youtube.com/watch?v=dgnKrfV4a7c
Buy whole car for $12,000 FIRM
Old sale thread with pictures http://forums.beyond.ca/st/198417/fs-1990-nissan-skyline/
EDIT: NOT PARTING ANYMORE