View Full Version : Adapter plate purchase
Police
12-06-2004, 08:49 PM
Where can I buy an adapter plate uncut that is 1/2 to 3/4 inch thick 4.5 by 4.5 for a turbo? and about how much would this cost?
djfob
12-06-2004, 09:06 PM
for what turbo and I'm assuming its for an hf/cx manifold?
finboy
12-06-2004, 09:10 PM
could be made for pretty cheap locally i believe
http://members.shaw.ca/rangermates/
check that guy out, does good work from what i've seen
Police
12-06-2004, 09:12 PM
yes CX/Hf manifold with the T3 chrysler turbo
Police
12-06-2004, 09:14 PM
Originally posted by finboy
could be made for pretty cheap locally i believe
http://members.shaw.ca/rangermates/
check that guy out, does good work from what i've seen
you're right:thumbsup:
Police
12-07-2004, 07:02 PM
^
djfob
12-07-2004, 08:01 PM
There are a few people on the net that sell adaptor plates for hf/t3s but the dodge t3 you got has a goofy not standard flange. I has an offset'd bolt which I guess you could redrill.
http://www.homemadeturbo.com/forum/index.php?board=4;action=display;threadid=25834
finboy
12-07-2004, 08:06 PM
Originally posted by djfob
There are a few people on the net that sell adaptor plates for hf/t3s but the dodge t3 you got has a goofy not standard flange. I has an offset'd bolt which I guess you could redrill.
http://www.homemadeturbo.com/forum/index.php?board=4;action=display;threadid=25834
werd, dodge housings are somewhat useless as none of the bolts line up with a standard t3 flange, i had to have my manifold re-studded to use a generic t3/t4 hybrid
Police
12-07-2004, 09:33 PM
yup i realize that haha
Sorry i didn't make myself clear enough lol, I only want to buy a plate that is 4.5 by 4.5 and 3/4 to 1/2 inch thick. This is a custom plate where i'm cutting and drilling everything. Where can i buy a piece of plate like that? welding shop?:dunno:
finboy
12-07-2004, 10:13 PM
metal scrap yard in foothills industrial
coolcat123
12-08-2004, 09:20 AM
it's called calgary steel, look it up in the phone book.
Police
12-08-2004, 10:24 PM
hmm anywhere near the North area or Edmonton trail?
Police
12-09-2004, 06:50 PM
^
Police
12-13-2004, 05:58 PM
bump
coolcat123
12-13-2004, 06:12 PM
Originally posted by Police
hmm anywhere near the North area or Edmonton trail?
look it up in the phone book scat man.
supaj87GTS
12-13-2004, 08:58 PM
Police I will Look at Work for you I work at a Metal Fabrication Shop I will Post back either tomorrow or Wed
For Free by the way
Jordan
rio_rex
12-13-2004, 10:20 PM
I went to calgary metal for that...just walk around in their yard and find a small peice thats lying around. They won't sell u a small chunk from their new steel as they have that 10 foot or more rule. I found a dencent sized peice and used a angle grinder with a cutoff disk to make it the size i needed.
Police
12-14-2004, 07:36 PM
^ sweet i think i'll take a look around...
Originally posted by supaj87GTS
Police I will Look at Work for you I work at a Metal Fabrication Shop I will Post back either tomorrow or Wed
For Free by the way
Jordan
thanks alot man if you can get one that would be great:thumbsup:
Police
12-15-2004, 09:42 PM
bump
Police
12-29-2004, 11:24 PM
^
Powered by vBulletin® Version 4.2.4 Copyright © 2024 vBulletin Solutions, Inc. All rights reserved.