PM'd
Type: Posts; User: JBreaks
PM'd
I'm looking for about a 14" straight piece of 2.5" ID aluminum inter cooler pipe. I'll take anything I can get thats cheap ass or free! willing to take any pieces that are kicking around
So hawt.
PM'd, I've got a d16y8 block and head available. I wouldn't assume it's a valve issue unless proven with a leak down test.. either way it's probably cheaply replaced or rebuilt.
http://www.kijiji.ca/v-tires-rims/calgary/15-4x100mm-honda-civic-oem-steel-rims-with-all-season-tires-95/1122435367
$400 on 4x100 steel rims, about as mint as it gets.
Your looking at:
-custom mounts & mounting within the body
-adding a clutch pedal, hydro lines and interior trim to accommodate a stick shift
-standalone ecu and harness
-custom drive shaft
...
factory tunes are rich amigos. Especially on anything factory boosted.
I've got some Apexi systems up for sale after going to Megasquirt Ms3x
AVC-R: Everything you need in perfect working order. Controller, pressure sensor, boost solenoid ect. with wiring harnesses...
You get it figured out?
D16 won't bolt up to a b-series transmission unfortunately. There are also considerations to be made as far as converting any car to obd1 to run the ecu with the tune for the turbo d16. I've got 7...
I bought the long block and other assorted parts from Sentry.. Just could not see this engine go to waste. The only weak point of this shameless civic was the junkyard turbo alone and I personally...
pull the vac tube off the fuel pressure regulator (block tube) and go for a drive. Seems like it might not be giving proper pressure under vacuum but fuel pressure increases enough under boost to run...
Sold.
check out the kijiji link:
http://www.kijiji.ca/v-tires-rims/calgary/motegi-ff7-17x7-40-rims-and-tires-5x114-3-5x100-bolt-patterns/1090936250?enableSearchNavigationFlag=true
Progressed on converting this car to MAP and IAT in prep for the Megasquirt ms3x that is currently being shipped.
Made a new longer intake pipe with no pcv return hose hole, as a new catch can...
bump
I've done it with a straight up dremel bit by hand and it turned out fine. re balanced the wheels though. Basically made no difference to balance because the material removed is so close to the axis...
bump
215/45/17 I believe.
See kijiji add:
http://www.kijiji.ca/v-tires-rims/calgary/motegi-ff7-17x7-40-rims-and-tires-5x114-3-5x100-bolt-patterns/1090936250?enableSearchNavigationFlag=true
17x7" + 42 Motegi's with...
Oem 2005 Infiniti G35 seven spoke alloy rims. 17" x 7" +40. Come with a set of lower profile Summer (says all season but I wouldnt touch snow with em) 215/45/17 rubber. Minor curb rash on one of 4....
An update on my plans for this summer:
Despite running nistune type 2 with a tune by Toma. I never got the results I wanted. The power at 20 psi was awesome, breaking traction shifting into second...
Changed rims and now no longer need these shim style 5mm spacers. $40 firm picked up form NW or meet Downtown or similar. Text 403-880-0419, please don't pm.
Could just be your wastegate being wide open or something. Are you running rich based on assumption or a wideband reading?
Basically the complete top half of a h22a4 from a 2000 SH, everything above the head gasket except the exhaust manifold. Comes with all sendsor with pigtails, solenoids, EGR, even have the...
Ebay amigo. BC's will be like $1k and megans $650
Got the rebuild under way. The amount of hard, white carbon I've been able to chip off the pistons/valves/head has been insane.
http://i.imgur.com/RBuniKC.jpg
intake, valve cover and distributor...
After making it through the winter I started running into some more bumps along the road in this build. It started with someone breaking in to steal my stereo head unit, followed by the oil cooler...
bump
1999 Prelude SH with 203,xxx km's. This car was being prepped for a turbo project (see build thread in my sig) and received a very high level of care and repair until it received some parking lot...
After a long cold sleep I'm getting ready to bring her back to life. Since the last update I've done:
-Newly wired ignition harness
-New set of LS2 coils
-New plugs
-Timing belt, idler and...
Looking to trade my 10 psi oem rb20 wastegate actuator for a oem sr20 or rb25 7 psi actuator. Needing lower boost for a different project.
Going to pop some adjustable cam gears into an RB20 to replace some rusting oem ones. Any info on cam adjustments would be appreciated. I do have tunable ecu, wideband ect. and I don't plan to mess...
This is a throttle position sensor type symptom... probe the middle wire with a needle using your mutimeter to test voltage from the wire to ground. Looking for 0.5v at closed throttle I think....
A little pre-winter-hibernation mode update:
The hood got mounted and received it's first layer of clear coat. Some more sanding for perfection and a layer or two and she will be ready to rock....
like increase the free play a bunch or is there a magic trick to it?
Zenki, you mean the freeplay at the pedal? I'll keep pumping it later tonight and see whats up.
Slave didnt seem to have any adjustment potential on its positioning, just straight bolt holes on the...
I got the clutch hydraulics pressured up after like 100 pumps and bled out any visible bubbles. I can see the slave cylinder moving about an inch when pedal is depressed... doesn't seem to want to...
I left this over the weekend, but I'll have to face it again soon, especially with the weather turning. I found that I can adjust the freeplay and master piston to increase the stroke length so Im...
Yup fluid flows from bleeder after every pump and hold cycle. Reservoir drops with pumping and has been filled repeatedly already without emptying and letting air into system.