The recall only affects push button start remote starters that the installer used a transmitter for the install. If you had two transmitters to start with and had two transmitters afterwards, you...
Type: Posts; User: Strugari
The recall only affects push button start remote starters that the installer used a transmitter for the install. If you had two transmitters to start with and had two transmitters afterwards, you...
On its way:thumbsup:
The CS275i is setup that way.
Sounds like you need a double pulse unlock, which can be changed in the programming.
shoot me an email and I will get you the manual:thumbsup:
I do have a manual. I am away from my computer right now.
Will send you a reply with manual when I return.
Thanks,
Gary.
:dunno:
I would say you either have a blown fuse, or a bad ignition switch.
Check for power at the pink ignition wire when you turn the key on.
The remote start is suppose to turn off when...
I have a manual.
email me at [email protected] with CS2500 manual in the subject line.
:thumbsup:
If it is a toyota there is a wire that will unlock the driver door with one pulse and all others doors with a second pulse. You can test this by unlocking the driver door with the key. If you give...
1. Open Hood
2. Press hood switch down and release
3. Lights will come on the vehicle
4. Before lights go out press and release the hood switch quickly
5. Lights should stay on
6. Press button...
More than likely a tach setting needs to be changed.
Make sure the white tach wire from the command start is connected to a tach source on the engine.
you can send an email to me at...
It is more than likely the antenna.
Check connection on the antenna to the clear plastic part on the windshield. Pull the antenna off (velcro) and re attatch it.
It sounds like the remote starter has a starter kill relay wired in. If you press the unlock on the remote then try to start it with the key does it start with the key?
If it does then the starter...
The antenna costs about $60.00 and the transmitters are $50.00The only problem is that it is impossible to tell if your unit is a 2 button or 4 button transmitter.
They are different.
I would have...
You got mail!
http://www.readyremote.com/autoCommandOEM.asp
Shoot their tech support an email with the part number.
That is an older autoCommand remote starter.
Do the lights still flash if you press button I?
If so you may have a faulty transmitter. Does the LED on the remote light up when you press button II?
Ebay have CS555 transmitters from time to time.
The on/off switch only shuts the remote start off. All other functions remain functional.
Gary
Shoot me an email [email protected]
Put CS301i in the subject line.
I will send the programming guide to you.
Gary
Check you power and ground. Check to make sure the switch is operating correctly. I have seen the switches be faulty causing no start situations.
Gary
The alarm must be tied in to the small yellow wire on the smaller harness of the remote starter.
If you pule that wire (yelloe) to ground, the remote starter should cycle and start the car.
If not,...
Try turning the switch under the dash off and back on.
The parklights on the car should flash 2 times slowly.
When you try to start the car how many flashes do you get on the car?
Shoot me an email at [email protected] and I will get you a install guide. Please put CS300 in the subject line.
Did you test the brake wire on the remote starter to see if there is any (+) feed on it during remote start?
You can also try cutting the wire to see if that helps.
shoot me an email at [email protected] with 290i in the subject line.
shoot me an email at [email protected]
Get me a pic of the unit and the transmitter and I should be able to help.
Thanks:thumbsup:
Is the vehicle a diesel?
If yes, you must program the unit to diesel mode.
If not, the unit is seeing 12V on the brake wire upon ignition. Check your tailight bulbs, if they are burnt, but not...
I have transmitters available and programming guides as well.
PM for pricing.
Could be in valet mode.
Turn the ignition switch on and off (NOT START) 5 times within 8 seconds.
Then try your remote start.
If that does not work will need a model number as there are lots...
Your remote may be faulty.
You can try reprogramming the remote transmitter.
Open hood
1. Press and release the hood switch (Parklights will come on)
2. While the lights are on press and...
Get under the dash to the unit.
You will see 8 or 9 dip switches on the unit with an LED beside them.
Turn switch 1 and 8 on.
Press and release the brake. (LED will flash)
Press and hold start...
Yes the 5 button and 6 button Astrostart transmitters do interchange.
The FCC ID number should end on J5f TX2000.:thumbsup:
The violet/white wire on the unit is a negative output.
I do think that you need to have (+) battery on your (+3)
If all else fails, you could use an ordinary relay wired as below.
Pin 85...
There is a sensor under the hood. It will be tied to either the top rad hose or the heater hose.
It will have two wires on it, (yellow or red).
These sensors are a very common problem.
If you cut...
Have both. PM me your email address with CS310i in the subject line and I will send them to you.:thumbsup:
It does sound like a command start. PM me your email address with CS330i in the subject line and I will send it out to you.:thumbsup:
PM me your email address and I will get a manual to you. Use CS290i as the subject line please:thumbsup:
I have fobs available.
PM me for a price
Thanks:thumbsup:
relay 1 - violet/white wire on Compustar unit
relay 2 - battery -
relay +3 - battery +
relay 4 - trunk popper
The output from the Compustar is a 400ma (-) output.
If you hooked bettery power...
Hi,
Sorry for the slow reply.
On the unit under the dash there is a brown wire on the 9 pin plug. (Larger plug)
This is the hood switch wire.
Using a test light, hook on side to graound, and...