Good place in calgary for custom exhaust work

[Freebs]

like the title says...Im wondering what place in calgary does good custom exhaust work for a good price. I know there was a post about this a while back but i can not find it any more... i just need a cat back made up but i want it a custom way that i have already worked out.

[buh_buh]

Carline

[88CRX]

do a search.......... everyone loves carline.

[LancerShelby]

Carline in the NE- Bay 6, 727 33St NE

[hockeybronx]

Yup, Carline a.k.a Calgary Muffler. That is one place that will value your business and take the time and effort to make you feel appreciated.

I personal recommend the 58th Ave and MacLeod Trail South location.

Here is a thread where we ranted and raved about it

http://forums.beyond.ca/showthread.p...algary+muffler

[Freebs]

Thanks alot... i shall be heading there as soon as my header arives

[legendboy]

I can do it for a bad price if you want

[Freebs]

Well i plan on going to Carline soon and asking, but for thoughs of you who have gone there before... do you know about how much it is going to cost me for a 2.25" or 2.5" single cat back exhaust? i have the cat. and the muffler.. just need them to fill in the missing pipes.

[gpomp]

150 ish for crush pipes

[Freebs]

$150 just for the pipes... or for every thing like labor and pipes? oh and do you know if that is stainless steel? i dont want my exhaust system rusting out on me.

[legendboy]

nobody can mandrel bend you an exhaust in calgary, aside from using ubends.

they will use aluminumized steel, which should hold up pretty good, but their welds, flanges and bolts will rust pretty bad.

they are definatly the best bang for your buck.

if you want a mandrel stainless exhaust i could do it for u but it will be pretty expensive

[Freebs]

i am not worried about what kind of bends they are... as it is just on a 4cyl. and the amount that it will actually effect the flow is very small... so couldnt i just get all stainless steel? i dont see why i would have to go with aluminumized steel for the bends?

[legendboy]

carline doesn't supply stainless. just go buy a cat back from speedtech

[Scat]

Originally posted by Freebs
i am not worried about what kind of bends they are... as it is just on a 4cyl. and the amount that it will actually effect the flow is very small... so couldnt i just get all stainless steel? i dont see why i would have to go with aluminumized steel for the bends?

Not just the bends will be aluminized steel, all of the piping will be. I don't know of any muffler shops that use stainless for their piping. Its just too expensive.

[Freebs]

hummm i find that hard to believe... i was just down at the world of wheels getting the car ready and i talked to a few people with custom exhausts and they said they were all done with stainless steel at local muffler shops...

But say i do go with Aluminized tubing.. how well does it hold up against rusting?

[DuPont]

Carline on Mcleod + 58th has done several of our customers cars with stainless. It is an arm and a leg for it though.

[Freebs]

Originally posted by DuPont
Carline on Mcleod + 58th has done several of our customers cars with stainless. It is an arm and a leg for it though.

yea i figured it would be pricey... how much would i except to pay for single cat back system with the stainless steel? in about a 2.5" diameter... also how well do you think the Aluminized tubing would stand up to rust? this is an every day all year around driver.

[supaj87GTS]

CARLINE

[pressure_ratio]

Originally posted by Freebs
hummm i find that hard to believe... i was just down at the world of wheels getting the car ready and i talked to a few people with custom exhausts and they said they were all done with stainless steel at local muffler shops...

But say i do go with Aluminized tubing.. how well does it hold up against rusting?

It's not that they can't do,it's just a pain and really expensive.if your going to weld stainless you need to change the wire and gas in your welder(I'd be surprised it they even have the argon and wire).Better yet if your going to spend the money get it tig welded,but thats waaaay beyond your average exhaust shop.
Aluminized is fine,just get them to spray the welds with a good high temp paint and it should last for years.

[legendboy]

I have a full thermal 3" turbo exhaust. All polished stainless. Phone speedtech for a price